Serving your shots and activating the L.E.D SHOT ROD™

4 Easy Steps:

  1. Prepare your shots / shooters
  2. On the L.E.D SHOT ROD™, connect the battery’s input / output termination with the controller’s input termination.
  3. Place the shot glasses in the L.E.D SHOT ROD™
  4. Turn the L.E.D SHOT ROD™ on using the remote control.

Remote Modes:

  1. Demo mode will switch through 9 dynamic modes, looped through 3 times
  2. Cycle through dynamic modes or switch to dynamic modes from static mode
  3. Increase speed of dynamic mode or switch to dynamic mode from static mode
  4. Increase brightness or switch to static mode from dynamic mode
  5. Decrease brightness or switch to static mode from dynamic mode
  6. Cycle through static modes or switch to static modes from dynamic mode
  7. Cycle through static modes or switch to static modes from dynamic mode
  8. Decrease speed of dynamic mode or switch to dynamic mode from static mode
  9. Cycle through dynamic modes or switch to dynamic modes from static mode
  10. On/Off

led shot glass holder

Charging the L.E.D SHOT ROD™

7 Easy Steps:

  1. Turn the L.E.D SHOT ROD™ off using the remote control.

  2. Disconnect, on the L.E.D SHOT ROD™, the battery’s input / output termination from the controller’s input termination.

  3.  Connect the power charger / adapter (supplied with the L.E.D SHOT ROD™) to the L.E.D SHOT ROD’S™ battery input / output termination.

  4.  Plug the power charger / adapter into a DC Block: the power charger / adapter indicator light is red indicating that the battery is charging.

  5.  When the power charger / adapter’s indicator light becomes green, then the battery is fully charged. Unplug the power charger / adapter from the DC Block, then unplug the power charger / adapter from battery’s input / output termination on the L.E.D SHOT ROD™.

  6.  Reconnect on the L.E.D SHOT ROD™, the battery’s input / output termination with the controller’s input termination.

  7. Turn the L.E.D SHOT ROD™ on using the remote control.

    (Recommendation: only reconnect the battery’s input / output termination with the controller’s input termination, immediately prior to usage, in order to not have any battery discharge effects).

led shot glass holder

The L.E.D SHOT ROD™ typical battery charging time is approximately 8 hours, however battery charging time will vary depending on the battery’s tank status. If you have just purchased the L.E.D SHOT ROD™ (new battery) or the battery has not been charged for several months, a full 8 hour charge is recommended.

When the battery is charging, the power adapter indicator light is red. When the battery is full and the charge over, the power adapter indicator light will change to green.

If you want to confirm whether the battery is full or not, you need to check the power adapter indicator; if the light on the power adapter becomes green when connecting to the L.E.D SHOT ROD™, the battery is full.

Cleaning and maintenance of the L.E.D SHOT ROD™

The L.E.D SHOT ROD™ is virtually maintenance free and its convenient design makes it easy to clean and very durable.

Most of the components and parts of the L.E.D SHOT ROD™ are interchangeable and it disposes of its specialized cleaning tools for faster turnaround time at the bar.

warningNever clean the L.E.D SHOT ROD™ by placing it in the dishwasher or submersing it completely under water.

To Properly & Safely Clean L.E.D Shot Rod™:

  1. Remove the shot glasses from the L.E.D SHOT ROD™ and gently wash them separately in a sink or dishwasher.
  2. Remove the end cap opposite the battery compartment of L.E.D SHOT ROD™
  3. Use a damp sponge, soap (dishwashing liquid) and water to wash and disinfect the outside of the device.
  4. Use a bottle (bristle) brush to easily clean the inner tube of the L.E.D SHOT ROD™
  5. Dry the L.E.D SHOT ROD™ both inside and outside using a dry cloth.
  6. Polish the L.E.D SHOT ROD™ using a stainless steel polisher and a dry cloth (stainless steel model only) for a shiny finish.

led shot glass holder

Share the love